| Part No | Manufacturer | Application |
|---|
| MAX218CWP | MAXIMIC | 1.8V to 4.25V - powered, true RS-232 dual transceiver. |
| MAX6316LUK46BZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX6318MHUK39CX-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX4445ESE | MAXIMIC | Ultra-high-speed, low-distortion, differential-to-single-ended line receiver with enable. |
| ICL8069BCSA | MAXIMIC | Low-voltage reference, 25 ppm/C - max temp. coefficient. |
| MAX4178EUK-T | MAXIMIC | 330MHz -3dB bandwidth, gain of +1, closed-loop buffer. |
| MAX4505EUK-T | MAXIMIC | Fault-protected, high-voltage, signal-line protector |
| MAX8211EJA | MAXIMIC | Microprocessor voltage monitor with programmable voltage detection. Define output current limit. |
| MAX3086ESD | MAXIMIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX4332ESA | MAXIMIC | Dual, low-power, single-supply, Rail-to-Rail I/O op amp. |
| MAX4304EUK-T | MAXIMIC | Low-noise, low-distortion op amp. Bandwidth 740MHz. Minimum stable gain 2V/V. |
| MAX6318MHUK29DZ-T | MAXIMIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| IH5042C/D | MAXIMIC | General-purpose CMOS analog switch. Single pole, double throw (SPDT) |
| MAX8211MTV | MAXIMIC | Microprocessor voltage monitor with programmable voltage detection. Define output current limit. |
| MXD1005PA100 | MAXIMIC | 5-tap silicon delay line |
| MAX365C/D | MAXIMIC | Precision, quad, SPST, normally open (NO) analog switch. |
| MAX337EPI | MAXIMIC | Dual 8-channel, low-leakage, CMOS analog multiplexer. |
| MAX736CWE | MAXIMIC | -12V, inverting carrent-mode PWM regulator. |
| MAX3486ECSA | MAXIMIC | 3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 2.5Mbps. Supply voltage 3.0V to 3.6V |
| MAX627C/D | MAXIMIC | Dual non-inverting power MOSFET driver. |
| MX581JESA | MAXIMIC | High precision 10 volt reference. Error +-30mV. |
| MAX6316MUK40CY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX1240BCPA | MAXIMIC | +2.7V, low-power, 12-bit serial ADCs in 8-pin SO. INL (LSB) +1 |
| MXD1013UA045 | MAXIMIC | 3-in-1 silicon delay line. Output delay 45ns. |
| DG507ACK | MAXIMIC | Monolithic CMOS differential 8 channel (2 of 16) analog multiplexer. |
| MAX4075ANESA | MAXIMIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 8V/V, noninverting gain 9V/V, -3dB BW 50kHz. |
| MAX1200BEMH | MAXIMIC | +5V single-supply, 1Msps, 16-bit self-calibrating ADC |
| MAX6321HPUK33AY-T | MAXIMIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX4539EPP | MAXIMIC | Low-voltage, single 8-to-1 calibration multiolexer. |
| MAX631BESA | MAXIMIC | CMOS fixed +5V output voltage,adjustable output with 2 resistors step-up switching regulator. 10% output accuracy. |
